grabcad
RC-Helicopter Blade
700 size Helicopter Rotor blade.
blade rc helicopter 3D Models
131 results
grabcad
grabcad
RC HELICOPTER BLADE
RC BLADE
grabcad
RC-Helicopter Blade
700 size Helicopter Rotor blade.
grabcad
RC Helicopter Blades
Solid works 2018
cults3d
RC Helicopter Blade cover
As part of my recycle of old RC Helicopter blades, they leave the ends exposed, and the...
prusaprinters
RC Helicopter Blade cover
As part of my recycle of old RC Helicopter blades, they leave the ends exposed, and the...
grabcad
RC Helicopter Rotor Blade
XK 130 Main Rotor Blade
thingiverse
RC Helicopter Blade cover
As part of my recycle of old RC Helicopter blades, they leave the ends exposed, and the...
thingiverse
RC HELICOPTER BLADE WALL MOUNT
4MM HOLE FOR WALL MOUNT
grabcad
blade holder for rc helicopter
reverse engineered part of an RC helicopter
grabcad
RC Helicopter tail rotor blade
RC Helicopter tail rotor blade
grabcad
Helicopter main rotor blade (RC)
Helicopter main rotor blade (RC)
grabcad
RC helicopter main rotor blade
span 16 cm,,, root chord: 1.5 cm tip chord: 1 cm maximum chord ~3 cm this is an arbitr...
grabcad
RC helicopter, rotor blade control
Modellezés
grabcad
RC helicopter, rotor blade control
Modellezés
cults3d
RC Helicopter Blade Holder (Hirobo SDX)
I designed this for my Hirobo SDX RC Helicopter. The tail boom is 21mm in diameter and ...
grabcad
5 Blade RC Helicopter Swash Head
A low profile, fully enclosed swashplate. I designed this rotor head a few years ago f...
grabcad
RC Helicopter 200 size 3 blade
Radio Controlled Helicopter 3D CAD model. 200 size electric with bladed propeller.
thingiverse
RC Helicopter Rotor blade tie rod
replacement RC helicopter part
thingiverse
RC Helicopter Blade Holder (Hirobo SDX)
I designed this for my Hirobo SDX RC Helicopter. The tail boom is 21mm in diameter and ...
thingiverse
Battery Holder for Blade 400 RC Helicopter
This plate will prevent your battery from rubbing on the brushless outrunner motor. ...
thingiverse
T-Rex 450 RC Helicopter Rotor Blade
This is a rotor blade for a T-Rex 450 RC Helicopter optimized for very stable flight. T...
thingiverse
RC helicopter landing gear for Blade Helis
Print your own landing gear for 150S ( and 180 but not sure) Blade RC Helis. Works wel...
thingiverse
Airwolf Blade for C119 or other RC Helicopter
I love Airwolf. But there is no rotor that looks the same as AirWolf and can be used o...
grabcad
RC Helicopter Rotor Blade for The Plastic Bank Challenge
My 2nd entry for https://grabcad.com/challenges/the-plastic-bank-challenge, 16 in span...
thingiverse
Coaxial RC helicopter blades (walkera, lama, e-sky)
Лопасти для старых соосных вертолётов класса lama v3 и подобных. Угол атаки ближе к кра...
cults3d
Reinforcement rods with fixings for RC Blade 200 SRX helicopter
Rods with fasteners to hold the tail of the helicopter in case of impact. Two of them m...
thingiverse
RC Helicopter Lower rotor head and blade holder assembly - prototype.
Update 16/11/2013; Sheering problem hopefully resolved. new model has been added as a r...
thingiverse
Revell Big One Pro RC Helicopter - Top Blade Gear and Hub
The old gear was loose on the shaft due to many crashes and I wasn't able to fasten it ...
thingiverse
RC Helicopter Lower rotor head and blade holder assembly - prototype. v5
THIS FILE HAS BEEN REPLACED WITH V7 OF THIS DESIGN FOUND AT; http://www.thingiverse.com...