myminifactory
ESC protector
Keep your ESC protected. This was designed to 18mm arm thikness, like Realacc X210 (on...
esc protectors 3D Models
208 results
myminifactory
thingiverse
ESC Protector
My take on quadcopter ESC protection. Will recommend printing with flexible, but pr...
thingiverse
ESC protector
Simple ESC protector, with and without a cutout for an RX wire if you want to mount you...
thingiverse
ESC protector
電變保護殼
thingiverse
ESC Protector
Fits XM20 size ESC, Racerstar MS25A etc..
thingiverse
ESC Protector
Untested for fit until this text is removed. My take on an ESC protector. This is desig...
thingiverse
Wraith32+ ESC Protectors
These covers fit the 50Amp Wraith32+ ESCS.. They are made of TPU for snug fit other mat...
thingiverse
slim esc protector
Just my design of an ESC protector for an fpv drone. Super Simple and useful.
myminifactory
ESC Protector Extended
This ESC protector has exteded tab to cover the weld pads. This feature is welcome esp...
thingiverse
x210 esc protector
An ESC protector for Realacc X210 Pro 3K
thingiverse
ESC protector mesh
ESC protector made specifically for Armattan Marmotte frame and Airbot Wraith ESCs, but...
prusaprinters
ESC + Capacitor Protector
It can cover ESCs with an outer dimension of 27x15x5mm with a 470uf capacitor.
thingiverse
ESC arm protector
Remixed protector to fit ECT packed into heat shrink. Original one had 4mm space and 3m...
thingiverse
ESC + Capacitor Protector
Designed for the Hobbywing XRotor Micro 30A ESCs with 470uf capacitors. It can hold ESC...
thingiverse
FPV ESC Protector
1 piece full ESC protectors with Zip the slits, that have a layer under the ESC so its ...
thingiverse
ESC cover/ protector
I have made this esc cover to fit the DYS Aria 32bit esc
thingiverse
ESC guard / protector
I made this to fit my spedex 30a ESC's. Hopefully it fits a wider range of ESC's Requi...
thingiverse
ButterFlight ESC protector
Two versions one with tree supports made in MeshMixer prints great standing up and supp...
thingiverse
Wraith32 ESC Protector
I designed this ESC cover for my FPV Quad as I usually used old props with electrical t...
thingiverse
RG20 ESC protector
After bent props destroying a few of my RG20 ECS's as well as constantly breaking the E...
thingiverse
Kiss24A ESC protector
I designed this ESC KISS 24A protector for the arms. There is enough room for 2 zip tie...
grabcad
ZMR250 ESC holder/protector for KISS ESCs
ESC holder for Kiss ESC. Fits ZMR250 arms. It is a loose fit, so you can keep the ESC's...
thingiverse
TBP x5 ESC Protectors
Protectores de varidores para el modelo de frame "TBP x5" de los fabricantes de Allcomp...
thingiverse
realacc x210 esc protectors
work in progress. print with tpu 0.2 print open side down on glass to make bottom smo...
thingiverse
Chaos 20A ESC protectors
A perfect ft for Chaos 20A ESC's, normally snap out the bottom bits so you can add or ...
thingiverse
ESC protector (fit's Tekko32 35A ESC)
I was damaging the caps on my ESC just a little to much but couldn't find a ESC protect...
thingiverse
ESC Protector Armattan Chameleon
ESC protector printed on blue TPU for Armattan Chameleon / TI Nozzle 220 ºC Speed 3...
cults3d
Esc protector for drone
Just another esc protector that fits in the realacc X210 frame, but now with a little d...
cults3d
ESC protector (Airbot Wraith)
Summary Print it from TPU or Nylon and mount it using tie wraps. It should work for ...
thingiverse
Betaflight 35A ESC Protector
ESC protector for the 35A Betaflight ESC. Mountable with 2 small zipties through the c...