thingiverse
Go pro handle bar mount
Printed at 100% so its solid. Should work on any handlebar with the same OD as a Ducati...
go pro handle bar mount 3D Models
22 results
thingiverse
thingiverse
Go Pro Mount for 22mm Handle Bar
This is a mount for a GoPro onto a 22mm OD handle bar. It is probably best to print in ...
thingiverse
Holt's Go Pro bike handle bar mount
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! h...
cults3d
Customizable Handlebar Mount
I only needed the handle bar bit, also the other one took an extremely long time to pro...
thingiverse
Customizable Handlebar Mount
I only needed the handle bar bit, also the other one took an extremely long time to pro...
thingiverse
Interceptor 650 go pro mount
Designed a simple go pro 3 finger mount for Royal Enfield Interceptor 650. This fits in...
prusaprinters
Customizable Handlebar Mount
I only needed the handle bar bit, also the other one took an extremely long time to pro...
thingiverse
Wilderness System Rail Cycle Accessory Mount
A slidetrax slide rail mounting accessory allowing the fitting of standard cycle handle...
thingiverse
GALILEO 2 SIDE CARRIER
The Arduino Mega is not quite powerful enough to handle GPS, Magnetometer, Acceleromete...
thingiverse
August Burns Red Flame
This is the logo for the band August Burns Red. The parts are designed to fit an Adafr...
cults3d
Armillary phone Holder
Here is the armillary Mount for smartphone. Ideal to keep your phone for a pleasant us...
thingiverse
Sonic Screwdriver For My Wife
This started out as a simple Laser pointer for my wife but since I cant leave well enou...
prusaprinters
LowRider 3 CNC - control box case for BTT SKR Pro 1.2 board and a BTT TFT35 E3 touchscreen (v1.3.4) SHORTER VERSION (180mm) FOR SHORTER PRINTERS
Quick heads up: These remix designs were somewhat “intended” for the case being positio...
prusaprinters
LowRider 3 CNC - control box case for BTT SKR Pro 1.2 board and a BTT TFT35 E3 touchscreen (v1.2)
Quick heads up: These remix designs were somewhat “intended” for the case being po...
prusaprinters
LowRider 3 CNC - control box case for BTT SKR 1.4 Turbo board, Raspberry Pi 4b, and BTT TFT35 E3 touchscreen (v1.3.5b)
This remix was requested by Stefan Raatz, who desired a case for holding an SKR 1.4 Tur...
cults3d
Solenoid Cage for Nerf Stryfe
This is a solenoid pusher assembly for the Nerf Stryfe. This cage will replace the sto...
cults3d
Solenoid Cage for Worker Swordfish
This is a solenoid pusher assembly for the Worker Swordfish. One cage assembly is comp...
thingiverse
Solenoid Cage for Nerf Stryfe
This is a solenoid pusher assembly for the Nerf Stryfe. This cage will replace the s...
thingiverse
Solenoid Cage for Worker Swordfish
This is a solenoid pusher assembly for the Worker Swordfish. One cage assembly is co...
prusaprinters
LowRider 3 CNC - control box case for Raspberry Pi 4b, BTT SKR Pro 1.2 board, and BTT TFT35 E3 touchscreen (v1.3.3)
This remix was requested by Miguel Arellano, who desired a 75 mm extension of an existi...
thingiverse
Open source bullet feeder / collator - 223/556 (Dillion 650, Hornady L&L etc)
****April 2019*** As a moron went and killed 50 people NZ is about to lose all acces...
thingiverse
The Cryptid: A Pump Action Clip Fed Nerf Sledgefire Conversion
What would be the Achilles Heel of a Sledgefire? The long reload cycle perhaps. And to ...