thingiverse
LED Light Pipe
Was for use in my LED Sectional Chart. Printed in clear resin on a Elegoo Saturn. Sized...
light pipe led 3D Models
707 resultsSponsored
thingiverse
thingiverse
LED Light Pipes
This is a group of test light pipes. The are designed to fit over a 5 mm thru-hole LED...
cults3d
LED Light Pipes
This is a group of test light pipes. The are designed to fit over a 5 mm thru-hole LED...
prusaprinters
Led light pipe holder
Led Light pipe holder
grabcad
Led Light Pipe 3mm
3mm Led Light PipeP/n:PLP2-188
thingiverse
RigidBot Heater LED Light Pipe
Small caps for putting the the circular pot adjustment openings near the extruders. Pr...
SPONSORED
🗳️ Will Keiko Fujimori win 2026 Peruvian election?
Latin American politics on the blockchain. Trade your conviction.
grabcad
light pipe for SMD LED
light pipe for SMD LED
cults3d
RigidBot Heater LED Light Pipe
Small caps for putting the the circular pot adjustment openings near the extruders. Pr...
prusaprinters
Amiga 1200 light pipe LED assembly
I made a ReAmiga 1.5 recently and it is in an A1200.net case. I made this from scratch ...
prusaprinters
Aviation Weather Map LED Light Pipe
This print is for holding addressable LED's used in this project: https://slingtsi.rue...
grabcad
LPF-S014331S LED Light Pipes
Data sheet - http://www.lumex.com/content/files/ProductAttachment/852015112302-LPF-S014...
prusaprinters
Light pipe (3mm) mount for 5mm LED
I needed to attach some light pipes to LEDs on a PCB, and these work fine although heat...
thingiverse
Clips - LED Light Pipe Tube & Wire Holder
Used these clips to mount a LED light stripe inside a light pipe (silicone tube) to the...
thingiverse
CR-6 SE Probe LED Light Pipe
My CR-6 SE printer is installed at such a height and angle from my seated position that...
prusaprinters
LED Light Pipe and Lens for Original Prusa MMU3
The LEDs on a stock MMU3 are difficult to see unless looking directly into the holes, e...
thingiverse
DAISO push light 4LED 28mm pipe bracket for APtrikes125
DAISO push light 4LED 28mm pipe bracket for APtrikes125
grabcad
515 Series Dialight Light Pipe
515-1141-100F/195F/220F/250F light pipes. Configurations in SolidWorks part for the dif...
thingiverse
Studio LED light with tripod
This is DIY studio LED light with PVC pipe. And 12v FCOB LED strip. Parts: - 20mm PVC ...
grabcad
Garden light column
Garden light with colored led strip around inner pipe
thingiverse
Light pipe mount for Neopixel
I'm doing a re-theme of an old EM pinball and needed a way to get light from a Neopixel...
cults3d
Nissan 300zx 1991 Door Handle Key Hole Illumination Light Pipe
Nissan 300zx 1991 Door Handle Key Hole Illumination Light Pipe Suits standard 5mm LED W...
thingiverse
Nissan 300zx 1991 Door Handle Key Hole Illumination Light Pipe
Nissan 300zx 1991 Door Handle Key Hole Illumination Light Pipe Suits standard 5mm LED ...
grabcad
shock and pressure resistant camera - sewage pipe robot project
shock and pressure resistant camera - sewage pipe robot project.Built-in zoomable optic...
thingiverse
Iphone S6 stand
This is a desk stand or bedside stand with a light so that the phone can be located in ...
cults3d
Solar/LED Light Mount
This is a Mount for a LED Light on a 100mm Rain Pipe. It's made for a LED Light with M...
thingiverse
Solar/LED Light Mount
This is a Mount for a LED Light on a 100mm Rain Pipe. It's made for a LED Light with...
thingiverse
Lid to 2" vvs pipe
Lid for 2" (5cm) vvs pipe, used in my case for vertical growing. Place lid on all pi...
myminifactory
diy desk lamp from leftovers
DIY desk lamp using a pvc pipe,a corrugated siphon, a mini dichroic led light, 2 printe...
thingiverse
Luxo Jr for 200x200mm printer with Led light
### Here is the Pixar Luxo Jr lamp totally 3D printed on 200x200mm bed and with led lig...
prusaprinters
4SQRP QRP Dummy Load Case
Print Instructions for the 4 State QRP Dummy Load Case.Print material: PLA, PLA+,...
Sponsored
Sponsored