thingiverse
P80 Drill Guide
Drill guide for use on P80 kits. Big enough to be useful, but small enough to use a min...
p80 drill guide 3D Models
99 resultsSponsored
thingiverse
thingiverse
Bowden filamentguide Geeetech i3 aluminium
I rebuild my Geeetech i3 pro for a bowden setup, and was in need for a new filament-gui...
thingiverse
Creality / Ender 3 Extruder Arm Screw Tensioner
I was tired of messing around with spacers and the likes and I had lost the spring for ...
thingiverse
Voron 2.4 Door Hinges (Bolt Through)
Voron 2.4 door hinges for 3mm panel.Doors can be opened 180 degrees Drill guide include...
thingiverse
Reprap Bed Leveling Sytem
Designed to fit the Prusa I2 base size of 220mmx220mm. Supports 4 point and 3 point hea...
prusaprinters
Drawer for Hoobro console
I needed a not too deep console table for the hall. Unfortunately, I can't find much of...
SPONSORED
🤖 Commercial humanoid robots under $10K by 2027?
The future of AI is tradeable. Predict tech breakthroughs.
thingiverse
4-Facet Drill Bit Sharpening Jig
A 4-facet point gives better cutting performance than a conventional point drill. a 4-f...
thingiverse
MGN12H for Predator
MGN12H for Predator necessary material: 3x 800mm MGN12H to attach the adapter ...
thingiverse
Drill Bit Sharpening Jig
A sharpening jig for small drill bits. Designed for drill bits with diameters of 1, 1...
thingiverse
623 Belt Guide / Spacer
623 belt guide / spacer During my build of my new Super Size Kossel I ran into the issu...
thingiverse
Heater Box for PTC element
Simple box with lid sized for a 77mm x 62mm x 6mm aluminum PTC heater element (e.g. htt...
cults3d
Precision level 14x100mm
Level of precision / engineer based on a glass HACCURY (4 '' / 2mm precision) bought on...
thingiverse
Lisam LS-180 and TC frame FPV Drone LED and Video Transmitter holder, VTX/Buzzer Mount and Camera Mount
This is a LED strip and Video transmitter holder for the Lisam LS-180 FPV Drone. You ca...
thingiverse
DVD / CD stepper slider unit
Inspired by this thing: https://www.thingiverse.com/thing:1765496 ... designed from s...
thingiverse
CR10/Ender 3 Extruder Chain with Filament Runout Mount
I remixed this using two different things on Thingiverse. I needed this in order to all...
prusaprinters
DVD / CD stepper slider unit
Inspired by this thing: https://www.thingiverse.com/thing:1765496 ... designed from sc...
thingiverse
Optical Filament sensor with M5Stack OP.180
This is a filament sensor that uses an off the shelf M5Stack OP.180 optical endstop. ...
thingiverse
Ender-3 V3 SE filament guide OUD
This filament guide is suitable for the Ender-3 V3 SE and can be installed in place of ...
thingiverse
Solidoodle 4 X-Motor Cable Guide and Fan Shroud
Cables tend to run over work surface, disrupting work in progress. Also, X motor gets e...
thingiverse
Ender-3 V3 SE filament guide
This filament guide is suitable for the Ender-3 V3 SE and can be installed in place of ...
prusaprinters
Heater Box for PTC element
Simple box with lid sized for a 77mm x 62mm x 6mm aluminum PTC heater element (e.g. htt...
thingiverse
Cube3 Back-2-Basics Nozzle Housing (B2B Project)
This is one of the three parts belonging to the Back-2-Basics Cube3 cartridge project (...
thingiverse
Felder Crosscut Fence Zero Clearance Insert
This is a zero-clearance for your Felder cross-cut fence. It will fit any Felder equipm...
thingiverse
Nano Brushless Drone (55mm frame size micro-Drone)
Printing parts (STL file name) Frame: [ TWBL55_frame_beta-FC.stl ] Camera mount b...
prusaprinters
Trim Router Circle Jig
I designed a simple circle cutting jig to be used with a trim router for cutting small ...
prusaprinters
Trim Router Circle Jig
I designed a simple circle cutting jig to be used with a trim router for cutting small ...
thingiverse
I3 MK3 and MK3S extruder for flexible materials
Update 14.11.2019: Caution !! There was a slight error in the extruder body, that ...
prusaprinters
Skadis T-Nuts Mounting System for Ikea Skadis Pegboards
These are T-Nuts for IKEA SKÅDIS pegboards that make installing accessories on your peg...
thingiverse
Airsoft electric toy gun
UPDATE Other AEG, my new projecthttps://www.thingiverse.com/thing:2916390 Warnings ====...
thingiverse
Anycubic Chiron Direct Drive Conversion with Factory Extruder & Hotend
This is a Direct Drive conversion using the factory Extruder, Hot End, Motor, Leveling ...
Sponsored
Sponsored